This is a 4-piece (2x2 pieces, 10x10 cm) 3D jigsaw puzzle of Shackleton crater, located at approximately 89.7°S, 128.0°E.  The model was created from the digital terrain model ldem_875s_5m, produced from Lunar Orbital Laser Altimeter (LOLA) data and available for download at:
http://pds-geosciences.wustl.edu/lro/lro-l-lola-3-rdr-v1/lrolol_1xxx/data/lola_gdr/polar/

You can view this feature in context on the Moon at:
https://quickmap.lroc.asu.edu/?extent=-154.8,-89.1,136.4,-88.4&proj=17&layers=NrBsFYBoAZIRnpEoAsjZwLraXOUNEQ4BmATnXm2yA

The included info sheet is intended to be printed out double-sided, and shows a map-projected LROC NAC image on one side, and a color shaded relief image on the other, both at the same scale as the puzzle.  The shaded relief map may be a useful reference when assembling the puzzle.

- - - 

This print has much looser tolerances than most LROC jigsaw puzzles (0.3 mm gap between pieces) and will likely print well on most printers.  However, the pieces do not lock together well enough to hold the puzzle together when picked up, and can be placed in the wrong positions.  You can try scaling the puzzle down to tighten the fit between pieces- 66% scale should be comparable to the other LROC puzzles (note that this will invalidate the scale information on the back side, however).

Our standard puzzle printing setup is as follows:
Layer height:  0.1 mm
Extrusion width:  0.4 mm (0.4 mm nozzle)
Top solid layers:  12 (diagonal pattern)
Bottom solid layers:  4 (diagonal pattern)
Perimeter shells:  3, printed outside-to-inside
Infill:  10%, rectilinear
Cooling fan:  Yes
No raft or brim, no support

Printer:  Fusion3 F400
Material:  Atomic Filament Silver PLA version 2
Bed:  Glass with a layer of purple glue stick, heated to 45°C
Slicer:  Simplify3D
(Disclaimer: This should not be interpreted as a formal endorsement of these products, it is simply documentation of what we use internally.)

- - -

Notes:

In general, the pieces should only need to be put together and taken apart a couple of times before they slide together cleanly and easily.  Note that the pieces must be kept aligned vertically while assembling or disassembling- any tilting will make it nearly impossible to slide them together.

I recommend trying to print a single pair of adjacent pieces and testing their fit as you tweak parameters until you get a good fit.  Pieces are numbered by column (letter) and row (number), where row 1 is the northernmost edge of the model, so A1 and A2 are a good adjacent pair to test.

- Any wobble or banding on the Z-axis will likely make the puzzle unusable- the walls must be perfectly vertical and smooth.  Filament thickness should also be very uniform.

- If you have any stringing, you will need to either carefully clean all the pieces after printing, or print pieces one at a time.

- The bed must be perfectly level, and the first layer should not be squished out (over-extruded) at all if possible.  If the first layer ends up wider than the others, you will need to trim it with a knife on every piece.  If your printer/bed/material combination needs to have an over-extruded bottom layer, try using a raft.

- If your slicer has a setting like "inset surface" to erode away the edges of the model, you might try using that to effectively increase the gap between pieces.  The effect on the surface topography should be negligible in most cases.

- You can also scale the puzzle up, which will effectively increase the gap between pieces.  Note, however, that doing so will invalidate the "xxx:1" scale information on the back side and make the info sheet no longer match the puzzle.

- - -

For more info about the Lunar Reconnaissance Orbiter Camera, visit lroc.sese.asu.edu

If you have any questions about printing this model, contact Robert Wagner (rvwagner@asu.edu).